Your shop runs on
sharp tooling.
Ours runs on software.
Ciklek manages your cutting tools the way a fleet company manages your vehicles — we track every blade, router bit, and planer knife, handle every service, and tell you when to retire before you have a problem.
You just run production.
Free audit — no commitment. We bring the scanner. Takes 30–60 min.
Trusted by 120+ cabinet and woodworking shops across the US
The real cost of dull tooling
You already know the pain.
Here's what it actually costs.
Most cabinet shops are absorbing thousands of dollars a month in hidden tooling costs — scrap, downtime, emergency sharpening, and over-retained blades. The audit makes it visible.
Tearout on expensive hardwood
A dull 80T ATB blade doesn't cut — it tears. On figured maple or quartersawn white oak at $18–$25 per board foot, one bad panel wipes out the margin on the entire job. You're not saving money by running a blade one more week.
Carbide tips are a safety incident waiting to happen
A carbide tip that lets go at 4,000 RPM becomes a projectile. Most shops have no way of knowing how many cycles a blade has been through or whether it's approaching structural failure. Ciklek tracks every cycle, per blade.
Emergency sharpening stops production
When a blade goes dull mid-run, someone drives it to the sharpening shop, waits, and drives back — or you swap to a substandard blade and accept worse cuts. A managed service means it never gets to that point.
Zero visibility into your tooling inventory
Ask most shop owners how many times their best blade has been sharpened. They don't know. Which blades are sharp? Which need service? Which should be retired? Ciklek answers all three — in real time, per tool.
How much is your shop losing?
Our free audit quantifies it. We scan your inventory, review your last 90 days of production, and put a real dollar figure on the tooling problem. Most shops are surprised.
Tools we service
Every tool in a cabinet shop
If it cuts wood, shapes profiles, or removes material — we track it, service it, and return it to spec.
Panel Saw Blades
ATB, TCG, combo profiles — all diameters
Router Bits
Spiral upcut, pattern, flush trim, molding
Planer Knives
HSS and carbide-tipped insert knives
Shaper Cutters
Raised panel, cope & stick, door profiles
CNC Router Bits
Compression, down-spiral, v-groove
Dado Sets
Stacked dado and wobble sets
Jointer Knives
Straight and helical insert heads
Bandsaw Blades
Resawing and scroll-cut profiles
How it works
Sharp tools.
Zero disruption.
Three steps. Your work never stops. Every tool tracked from pickup to delivery.
We pick up — and etch
Pick a pickup window that fits your day, between services, appointments or shifts. Your driver brings a portable QR etching machine and gives each tool a unique code engraved into the metal in about 5 seconds. No labels or stickers to fall off. New tools are registered and etched on the spot.
We send to the experts
Your tools go to a partner service center that specializes in them, with a work order giving the exact geometry for each one: edge angle, bevel, steel or carbide grade, grind method, tolerances. They sharpen to spec and send them back.
We verify and deliver
Every tool is QC-checked against its spec when it returns. Measurements logged. Photos taken. Anything outside tolerance is flagged before it gets back to your shop. Then it's back in your kitchen, chair or shop, sharp and tracked.
The spec sheet difference
Every tool has a technical contract
Generic sharpening services grind everything to one standard angle. We keep a spec for each tool (edge angle, bevel, steel or carbide grade, grind method, tolerances) and send it with every batch. Your 15° Japanese gyuto comes back at 15°, your convex shears come back convex, and your Freud blade keeps its factory hook.
- Edge, bevel & hook angle targets with ±tolerance band
- Steel, carbide grade and coating specifications
- Grind method (whetstone, CBN, diamond, aluminum oxide)
- Material-removal tracking: retire before it's unsafe
- Maximum resharpening cycles enforced automatically
Your profiles. Your specs. Every time.
Cabinet shop tooling isn't generic. A 5-piece door profile router bit has a very specific geometry — and if the service center gets it wrong, you'll know the moment you run a test piece. Ciklek stores the spec for every tool and ships a work order with each batch so the service center knows exactly what they're dealing with.
Spec on file
Hook angle, bevel, grind wheel, carbide grade — stored per tool at registration.
Work order per batch
Printed spec sheet ships with every batch. No phone calls, no guesswork.
QC on return
Actual vs target measurements logged. Anything outside tolerance is flagged before delivery.
From the blog
Tooling knowledge for cabinet shops
Deep dives on blade geometry, cost analysis, and maintenance programs written for cabinet makers.
The Hidden Cost of Running Dull Blades
Most shop owners track material costs religiously but ignore the single biggest driver of scrap: tooling condition. Here's how to read your scrap rate as a tooling health signal.
When a Saw Blade Becomes a Safety Hazard: The Carbide Tip Risk Most Shops Ignore
A carbide tip ejected at 4,000 RPM travels at over 200 mph. Most shops have no idea how close their blades are to that failure point.
Planer Knives: The Most Neglected Tool in the Cabinet Shop
Every shop changes their saw blades. Almost nobody manages their planer knives with the same discipline — and it's quietly destroying surface quality.
Why Premium Hardwoods Demand a Different Tooling Standard
When you're cutting $22/bf figured walnut, a $35 sharpening isn't a cost — it's insurance. Here's why material value changes the entire tooling calculus.
5 Signs Your Router Bit Is Past Its Prime (And Silently Costing You Money)
Router bits are the most under-maintained tool in most shops. Here's how to read the signals before they become problems.
Features
Built for the people who cut
Every feature exists because a chef, stylist or shop owner told us something was broken.
Permanent QR etching
Your driver carries a portable etching machine. Every tool gets a unique QR code engraved into the metal at first pickup — no labels to fall off, no stickers to fade. The code survives sharpening and lasts the life of the tool.
Standing spec sheets
Edge angle, bevel, steel or carbide grade, grind method, tolerances, stored per tool. Your chef's knife and your saw blade each come back the same way every time.
Multi-shop batch shipping
We consolidate tools from across all your locations into a single service batch. One shipment, one work order, maximum turnaround efficiency.
Work order PDFs
A printed spec sheet ships with every batch. The service center knows exactly what to do with each tool — no calls, no guesswork.
Wear tracking
Every sharpening removes material. We track blade width, plate thickness and edge length over time and flag tools nearing their safe limit before they fail.
Retirement & cycle alerts
Max resharpening cycles enforced per model. System alerts you when a tool is due for replacement, before it fails mid-cut.
QC verification on return
Returned tools are checked against their spec before going back to your shop. Actual vs target measurements logged. Photos taken. Nothing skips QC.
Customer portal
See every tool, every service event, every batch status in real time. Download spec sheets, service history, or retirement reports.
Automated invoicing
Invoice generated and emailed after every delivery. Itemized by tool and service type. Pay online. Syncs to QuickBooks.
Discounted tooling supply
Buy replacement tools through Ciklek at volume pricing — typically 10–20% below retail. Pre-registered before arrival.
Blade-as-a-Service
Flat monthly fee covers supply, service, and replacement. We own the inventory. You run your business and never touch a purchase order.
Multi-location accounts
Multiple locations, one account. Separate pickup addresses, combined billing. Account managers see everything across all your sites.
Pricing
Pay for what you use.
Nothing else.
No monthly fees. No contracts. No tool limits. You're charged when we pick up and when tools are done — that's it.
Per Pickup
Flat fee every time we come to your shop — regardless of how many tools are in the batch. Covers pickup, transport to our service center, and return delivery.
- Free scheduling via customer portal
- Driver scans every tool on pickup
- QR-tracked from door to door
- Return delivery included
Per Saw Blade Sharpened
Charged per carbide saw blade once sharpening is complete and QC-verified, before your tools head back. Knives, scissors, drill bits and other tools are priced by type. Ask us for a quote.
- Carbide resharpen to original spec
- Before & after condition logged
- Wear level & retirement alerts
- Full service history in your portal
Example job
12 blades
Typical cabinet-shop batch
$30 + $180
$30 pickup + 12 × $15
$210 total
vs $1,440 to replace them new
$0
to get started — free audit, free QR labels, free first pickup
No lock-in
book as needed, cancel anytime, no contract required
48–72 hr
standard turnaround, pickup to delivery
Enterprise accounts with high volume? Talk to us about custom rates.
Get started
We track every tool,
handle every service,
and tell you when to retire
before you have a problem.
You just run your business.
Serving restaurants, salons, shops and crews across the Bay Area.